Emulsogen LCN 158
In waterborne and solvent-borne lacquers (low PVC), Emulsogen LCN 158 can be used as a compatibilizer to improve tinting strength and to reduce rub-out, water absorption, and haze effects. Dosage recommendation (supply form) in waterborne acrylic lacquers is 1.3-1.9% and in solvent-borne alkyd lacquers 0.33-0.66%.
When used during the premixing phase in the production of waterborne emulsion paints (high PVC), Emulsogen LCN 158 also acts as a processing aid and helps to reduce the grinding time by faster deagglomeration of TiO2 and fillers. This is especially of interest in areas of hard water. The general dosage recommendation (supply form) for this purpose is 0.3%.
Product Information
The use of Emulsogen LCN 158 offers the following advantages:
Product properties:
•low VOC
•free of alkylphenol ethoxylates (APEO)
•readily biodegradable
•easy to handle (liquid material; soluble in water)
•FDA approved
Performance as emulsifier in emulsion polymerization:
•maintains low viscosity of polymer emulsion at different shear rates
•enhanced electrolyte stability
•improved shelf life (high freeze thaw stability)
•similar polymerization results to APEOs
•Dosage level is 2 % based on monomers.
Performance as compatibilizer in water-borne acrylic lacquers (low PVC):
•prevents rub-out effects
•increased tinting strength
•improved wetting of the coated surface
•good adhesion on polyethylene
•reduced water absorption
•use recommendation: 1.0 - 1.5% active dosage, 1.3 - 1.9% supply dosage
Performance as compatibilizer in solvent-borne alkyd lacquers (low PVC):
•prevents rub-out effects
•increased tinting strength
•reduced haze
•good adhesion on metal and zinc
•no impact on storage stability
•no yellowing effects
•no influence on surface drying and overpaintability performance
•no blocking effects
•use recommendation: 0.25 - 0.5% active dosage, 0.33 - 0.66% supply dosage
Performance as process aid in the production of water-borne emulsion paints (high PVC):
•reduces the grinding time by faster desagglomeration of TiO2 and fillers in slurries
•less energy consumption and more production capacity
•use recommendation: 0.3% supply dosage
- Nonionic emulsifier
- Fatty alcohol ethoxylates
- Emulsion polymerization
- Waterborne paints
- Decorative paints
| Product group: | Fatty alcohol ethoxylate |
| Active content: | 80% |
| Appearance: | clear liquid |
| pH value: | 6 - 8 |
| Solubility: | soluble in water |
| Density: | approx. 1.06 g/cm3 |
| Viscosity: | approx. 230 mPas |
| Crystallisation temperature: | 5 °C |
| Flash point: | > 140 °C |
| HLB value: | 16 |
Use as nonionic emulsifier in emulsion polymerization:
•Styrene/acrylate dispersions
•Acrylate dispersions
•Vinyl acetate dispersions
•Butadiene/styrene latex
•dosage level is 2% based on monomers.
Use as compatibilizer:
•water-borne acrylic lacquers (low PVC): use recommendation: 1.0-1.5% active dosage, 1.3-1.9% supply dosage
•solvent-borne alkyd lacquers (low PVC): use recommendation: 0.25-0.5% active dosage, 0.33-0.66% supply dosage
Use as process aid:
•in the production of water-borne emulsion paints (high PVC): use recommendation: 0.3% supply dosage
