PC+ABS-GF15
3D printer filament

PC+ABS-GF15

3D printer filament

版本编号 :
20190721
版本日期 :
2019年07月21日
Clariant 15% Glass Fiber Reinforced PC+ABS (PC+ABS-GF15) is created by adding 15% glass fibers to a Polycarbonate + Acrylonitrile Butadiene Styrene (PC+ABS) polymer blend to provide a strong and tough material with improved resistance to warpage during printing. Clariant additives are added via a Renol® masterbatch to improve the heat stability and resistance to thermo-oxidative degradation and yellowing. 
优点
  • Strong and tough engineering thermoplastic
  • High impact strength
  • High heat resistance
  • Good low temperature ductility
  • Glass reinforcement helps minimize warping during printing
  • Reduced thermo-oxidative degradation
  • Minimized undesired yellowing due to ultraviolet light

Applications*
  • Mechanical and technical application parts that require strength and toughness
  • Prototypes
  • Tools, jigs, fixtures
*Subject to detailed product specifications.

Color Range
Standard
  • Black
ColorWorks® ColorForward® consumer color directions 2019
  • MADE IN HUMAN - Protect the core (red)
  • DO NOT DISTURB - ἀταραξία von has fidanken (green blue)
ColorWorks® ColorForward® consumer color directions 2020
  • EYE AM WATCHED - Catch me if you can (orange)
  • Print Temperature = 260-285°C
  • Print Speed = 20-50 mm/s
  • Bed Adhesion = a thin coating of PVP glue on glass or carbon fiber
  • Bed Temperature = ideally heated up to 110°C (use an enclosed chamber if possible)
  • Fan Settings = low

Note: parameters are dependent on printer used; Clariant tests were performed on Ultimaker S5 and 3ntr A4 V3 printers.

Property Typical ValuesUnitsTest MethodTest Specimen
  blackfidankenanatural   
MECHANICAL PROPERTIES       
Tensile stress at yield, 50 mm/min



MPaISO 527Injection molded
 
n/an/a
MPaISO 5273D printed XY / flat at 280°C
 
n/an/a
MPaISO 5273D printed XZ / on edge at 280°C
 
n/a15
MPaISO 5273D printed ZX / upright at 280°C
Tensile stress at break, 50 mm/min
78

MPaISO 527Injection molded
 
4949
MPaISO 5273D printed XY / flat at 280°C
 
6558
MPaISO 5273D printed XZ / on edge at 280°C
 
2119
MPaISO 5273D printed ZX / upright at 280°C
Tensile elongation at yield, 50 mm/min 

 %ISO 527Injection molded
  n/an/a %ISO 5273D printed XY / flat at 280°C
  n/an/a %ISO 5273D printed XZ / on edge at 280°C
  n/a0.5 %ISO 5273D printed ZX / upright at 280°C
Tensile elongation at break, 50 mm/min
6

%ISO 527Injection molded
 
1.32.1 %ISO 5273D printed XY / flat at 280°C
 
2.31.8 %ISO 5273D printed XZ / on edge at 280°C
 
0.80.7 %ISO 5273D printed ZX / upright at 280°C
Tensile modulus (modulus of elasticity), 1 mm/min    MPaISO 527Injection molded
  44493480 MPaISO 5273D printed XY / flat at 280°C
  45714082 MPaISO 5273D printed XZ / on edge at 280°C
  22311885 MPaISO 5273D printed ZX / upright at 280°C
Flexural modulus
4410

MPaISO 178injection molded
Flexural strength
122

MPaISO 178Injection molded
Izod impact notched
12

kJ/m2ISO 180Injection molded
Charpy impact notched
13

kJ/m2ISO 179Injection molded


3226
kJ/m2ISO 1793D printed XY / flat at 280°C
THERMAL PROPERTIES       
Melting point



 ISO 11357, DSCb 
Glass transition temperature
112, 145

°CISO 11357, DSCb 
Heat deflection temperature at 1.8 MPa (A)
120

°CISO 75Injection molded
  125121 °CISO 753D printed XY / flat at 280°C
Heat deflection temperature at 0.45 MPa (B)
134

°CISO 75Injection molded
  131125 °CISO 753D printed XY / flat at 280°C
GENERAL PROPERTIES       
Density 1251  kg/m3ISO 1183 
Volume    cm3ISO 1183 
pH    

1% in H2O
Water absorption 0.41  % ISO 6224 hours at 23°C
Water content - coulometric Karl Fischer
   μg/gISO 12937after drying at 120°C for 2 hours
Water content 0.02  %
ISO 15512after drying at 120°C for 2 hours
non-volatile-matter content
   %ISO 3251 
a. Organic based color. b. DSC = Differential Scanning Calorimetry at 10°C/minute.
Note: results are generated according to the valid testing standards indicated above and the standard operating procedures used by the testing facilities.
Delivery form
1.75 mm and 2.85 mm diameter 3D printer filament.

Packaging
1 kg and 5 kg spools of 3D printer filament. Custom sizes are available upon request.

Storage
Ideally store the 3D printer filament in a cool, dry place at temperatures between 5 to 25°C in a sealed container with the provided Clariant Desi Pak® desiccant bag. If the 3D printer filament has been exposed to moisture, please dry at 100-110°C for 3-4 hours with a vacuum or desiccant drying system if possible. Minimum shelf life is 1 year from the date of shipping when properly stored.
3D Printing
3D Printing
Contact

向科莱恩发送请求

Related products

向科莱恩发送请求

请输入您的联络信息以便我们处理您的请求。感谢您的关注。

3D Printing
3D Printing
Contact
免责声明:
此信息基于我们目前的知识水平,用于对我们产品和可能应用的一般描述。科莱恩不对此信息的准确性、适当性、充分性或无缺陷做出任何明示或默认保证,并且对使用此信息不承担任何相关责任。产品用户有责任确定该产品是否适合特定应用。<br />
<br />
*此信息与科莱恩销售的一般条款和条件无冲突,除非采用书面形式另加说明,否则以一般条款和条件为准。必须遵守所有现有的知识/工业产权。由于我们的产品及其适用的国家/地区和国际法律法规可能变化,我们的产品状态也可能发生改变。处置或存放科莱恩产品时,必须遵循材料安全数据表规定的安全措施,材料安全数据表将按适用法律规定和用户要求提供。在处置这些产品前,您应当获取并浏览适用的材料安全数据表信息。了解更多信息,请联系科莱恩。<br />
<br />
*此外,以下限制适用于美国和加拿大境内的客户:对任何产品或服务的适销性、适合性、特定用途适用性和其他,不作任何明示或默认保证。<br />
<br />
© 科莱恩已在许多国家/地区注册商标。<br />
® 2019 年科莱恩国际有限公司版权所有 

您即将离开 Clariant.com 页面

您点击的链接将在 10 秒内带您离开 Clariant.com 网站页面。 若想停止此操作,单击“取消”。